Concrete Cutting O'Connor
Concrete cutting, core drilling, sawing, grinding and GPR scanning in O'Connor for builders, trades and homeowners. O'Connor is part of our Fremantle & Cockburn service area, about 10–25 min from our base in Myaree.
Concrete cutting in O'Connor
We work with facility managers and contractors in O'Connor on factory floors, hardstands and loading docks, with permits and inductions sorted before we arrive.
O'Connor is one of Perth's working industrial areas. We cut and core in warehouses, factories and yards, often around operating equipment. We regularly work in O'Connor's commercial and industrial buildings, so site inductions, permits to work and operating equipment are all part of the plan.
We complete site inductions and work within your O'Connor site's permit system. Every job follows the same process: scan, mark and protect, cut, then remove and clean up.
- GPR scanning before anchor drilling and fixings
- Trench cutting for drainage, power and data in factory floors
- Cutting out and removing slabs for machine bases
- Large-diameter core holes for services and ducting
- Joint sawing and re-sawing hardstands and warehouse floors
Our services in O'Connor
Cutting, coring, scanning, grinding and removal from one crew.
Concrete CuttingConcrete Cutting
Wall, slab and hand sawing for openings, trenches and removals in reinforced concrete, block and brick.
Concrete Cutting
Floor SawingFloor Sawing
Walk-behind saws for slabs, trenches, control joints, driveways and road surfaces.
Floor Sawing
Wall SawingWall Sawing
Track-mounted and hand sawing for doorways, windows and openings in concrete and masonry walls.
Wall Sawing
Core DrillingCore Drilling
Round holes through floors, walls and ceilings for plumbing, electrical, fire services and ducting.
Core Drilling
Floor GrindingFloor Grinding
Grinding slabs to remove coatings and adhesive, level high spots and prepare for new finishes.
Floor Grinding
Concrete ScanningConcrete Scanning
Ground-penetrating radar to find rebar, post-tension cables, conduits and voids before you cut or drill.
Concrete Scanning
DemolitionDemolition
Controlled concrete removal: slabs, walls, footings, steps and paving, broken out and taken away.
Demolition
Road & Driveway SawingRoad & Driveway Sawing
Asphalt and concrete sawing for crossovers, driveways, kerbs, car parks and service trenches.
Road & Driveway SawingHow we work in O'Connor
Scan
We scan with ground-penetrating radar to find rebar, post-tension cables and conduits before anything is cut.
Mark and protect
Cut lines are agreed and marked. Floors, walls and finishes nearby are covered and water suppression is set up.
Cut
Diamond saws and core drills cut to the line, with water and slurry captured as we go.
Remove and clean up
Sections are lifted out, waste goes to certified recycling or disposal, and the area is left clean for the next trade.
O'Connor questions
Do you do concrete cutting in O'Connor?
Yes. O'Connor is part of our Fremantle & Cockburn service area, about 10–25 min from our base in Myaree. Call 0423 303 210 for availability.
Do you scan before cutting or coring in O'Connor?
Yes. We use ground-penetrating radar to find rebar, post-tension cables and conduits before we cut, so there are no surprises in the slab.
How much does concrete cutting cost in O'Connor?
It depends on the thickness and reinforcement of the concrete, the length or number of cuts and cores, and site access. Send us the details or a photo and we'll give you a clear price.
Do I need a council permit for concrete cutting in O'Connor?
Work inside your property usually doesn't need one. Cutting crossovers, kerbs or anything in the verge or road reserve may need approval from the City of Fremantle. We'll tell you what applies when we quote.
Tell us what needs cutting, where it is and when you need it done. We'll give you a clear price and a time we'll actually turn up.