- Home
- Service areas
- South-East Corridor
- Kelmscott
Concrete Cutting Kelmscott
Concrete cutting, core drilling, sawing, grinding and GPR scanning in Kelmscott for builders, trades and homeowners. Kelmscott is part of our South-East Corridor service area, about 20–45 min from our base in Myaree.
Concrete cutting in Kelmscott
Most of our Kelmscott work is on established homes and local businesses: renovations, extensions and the plumbers and electricians who need a clean hole in the right place.
Kelmscott has plenty of older slabs and brickwork. We scan first, cut to the line you've marked and leave the area clean for the next trade.
Most residential jobs in Kelmscott are done in a single visit by one crew. Every job follows the same process: scan, mark and protect, cut, then remove and clean up.
- Driveway and crossover cutting
- Grinding floors back for new coverings
- Small demolition: steps, paths, footings and slabs
- Plumbing trenches through house slabs for renovations
- Core holes for downpipes, plumbing and air-conditioning
Our services in Kelmscott
Cutting, coring, scanning, grinding and removal from one crew.
Concrete CuttingConcrete Cutting
Wall, slab and hand sawing for openings, trenches and removals in reinforced concrete, block and brick.
Concrete Cutting
Floor SawingFloor Sawing
Walk-behind saws for slabs, trenches, control joints, driveways and road surfaces.
Floor Sawing
Wall SawingWall Sawing
Track-mounted and hand sawing for doorways, windows and openings in concrete and masonry walls.
Wall Sawing
Core DrillingCore Drilling
Round holes through floors, walls and ceilings for plumbing, electrical, fire services and ducting.
Core Drilling
Floor GrindingFloor Grinding
Grinding slabs to remove coatings and adhesive, level high spots and prepare for new finishes.
Floor Grinding
Concrete ScanningConcrete Scanning
Ground-penetrating radar to find rebar, post-tension cables, conduits and voids before you cut or drill.
Concrete Scanning
DemolitionDemolition
Controlled concrete removal: slabs, walls, footings, steps and paving, broken out and taken away.
Demolition
Road & Driveway SawingRoad & Driveway Sawing
Asphalt and concrete sawing for crossovers, driveways, kerbs, car parks and service trenches.
Road & Driveway SawingHow we work in Kelmscott
Scan
We scan with ground-penetrating radar to find rebar, post-tension cables and conduits before anything is cut.
Mark and protect
Cut lines are agreed and marked. Floors, walls and finishes nearby are covered and water suppression is set up.
Cut
Diamond saws and core drills cut to the line, with water and slurry captured as we go.
Remove and clean up
Sections are lifted out, waste goes to certified recycling or disposal, and the area is left clean for the next trade.
Kelmscott questions
Do you do concrete cutting in Kelmscott?
Yes. Kelmscott is part of our South-East Corridor service area, about 20–45 min from our base in Myaree. Call 0423 303 210 for availability.
Do you scan before cutting or coring in Kelmscott?
Yes. We use ground-penetrating radar to find rebar, post-tension cables and conduits before we cut, so there are no surprises in the slab.
How much does concrete cutting cost in Kelmscott?
It depends on the thickness and reinforcement of the concrete, the length or number of cuts and cores, and site access. Send us the details or a photo and we'll give you a clear price.
Do I need a council permit for concrete cutting in Kelmscott?
Work inside your property usually doesn't need one. Cutting crossovers, kerbs or anything in the verge or road reserve may need approval from the City of Armadale. We'll tell you what applies when we quote.
Tell us what needs cutting, where it is and when you need it done. We'll give you a clear price and a time we'll actually turn up.