- Home
- Service areas
- North-East & Swan
- Herne Hill
Concrete Cutting Herne Hill
Concrete cutting, core drilling, sawing, grinding and GPR scanning in Herne Hill for builders, trades and homeowners. Herne Hill is part of our North-East & Swan service area, about 25–45 min from our base in Myaree.
Concrete cutting in Herne Hill
Bigger blocks and older homes in Herne Hill mean a mix of slab work, wall openings and small demolition. We price the job clearly before we start.
Properties around Herne Hill come with sheds, retaining walls, water tanks and long driveways. We bring the right gear and plan for the access.
If water or power is limited on your Herne Hill site, tell us when you book and we'll come prepared. Every job follows the same process: scan, mark and protect, cut, then remove and clean up.
- Wall openings in older brick and stone homes
- Removing old slabs, paths and footings
- Joint sawing new shed and workshop floors
- Grinding garage and workshop floors
- Cutting shed and garage slabs for new doors or services
Our services in Herne Hill
Cutting, coring, scanning, grinding and removal from one crew.
Concrete CuttingConcrete Cutting
Wall, slab and hand sawing for openings, trenches and removals in reinforced concrete, block and brick.
Concrete Cutting
Floor SawingFloor Sawing
Walk-behind saws for slabs, trenches, control joints, driveways and road surfaces.
Floor Sawing
Wall SawingWall Sawing
Track-mounted and hand sawing for doorways, windows and openings in concrete and masonry walls.
Wall Sawing
Core DrillingCore Drilling
Round holes through floors, walls and ceilings for plumbing, electrical, fire services and ducting.
Core Drilling
Floor GrindingFloor Grinding
Grinding slabs to remove coatings and adhesive, level high spots and prepare for new finishes.
Floor Grinding
Concrete ScanningConcrete Scanning
Ground-penetrating radar to find rebar, post-tension cables, conduits and voids before you cut or drill.
Concrete Scanning
DemolitionDemolition
Controlled concrete removal: slabs, walls, footings, steps and paving, broken out and taken away.
Demolition
Road & Driveway SawingRoad & Driveway Sawing
Asphalt and concrete sawing for crossovers, driveways, kerbs, car parks and service trenches.
Road & Driveway SawingHow we work in Herne Hill
Scan
We scan with ground-penetrating radar to find rebar, post-tension cables and conduits before anything is cut.
Mark and protect
Cut lines are agreed and marked. Floors, walls and finishes nearby are covered and water suppression is set up.
Cut
Diamond saws and core drills cut to the line, with water and slurry captured as we go.
Remove and clean up
Sections are lifted out, waste goes to certified recycling or disposal, and the area is left clean for the next trade.
Herne Hill questions
Do you do concrete cutting in Herne Hill?
Yes. Herne Hill is part of our North-East & Swan service area, about 25–45 min from our base in Myaree. Call 0423 303 210 for availability.
Do you scan before cutting or coring in Herne Hill?
Yes. We use ground-penetrating radar to find rebar, post-tension cables and conduits before we cut, so there are no surprises in the slab.
Do I need a council permit for concrete cutting in Herne Hill?
Work inside your property usually doesn't need one. Cutting crossovers, kerbs or anything in the verge or road reserve may need approval from the City of Swan. We'll tell you what applies when we quote.
How much does concrete cutting cost in Herne Hill?
It depends on the thickness and reinforcement of the concrete, the length or number of cuts and cores, and site access. Send us the details or a photo and we'll give you a clear price.
Tell us what needs cutting, where it is and when you need it done. We'll give you a clear price and a time we'll actually turn up.